Helpy 2W-LCP

Helpy 2W-LCP is the 2-wires solution for MRL control panels, to be installed on elevator controllers or in the machine room.

Modular autodialler specifically designed for installation on elevator controllers.

5HL-300 Helpy 2W-LCP 12V: Autodialler ready for connection to the dedicated GSM200-C module and expandible over the PSTN-line with the add-on board.

5HL-310 Helpy 2W-LCP PSTN 12V: Autodialler ready for connection over the PSTN line or universal GSM gateway (PSTN-line board included)

5HL-320 Helpy 2W-LCP 24V: Autodialler ready for connection to the dedicated GSM200-C module and expandible over the PSTN-line with the add-on board.

LCP Details

New 2-wires autodiallers:

reduced cabling thanks to the new proprietary 2W-BUS and enhanced diagnostic
complete range of dedicated 2W speaker units: the perfect-matching solution for any installation with the utmost quality-speech
periodic BUS check with programmable notifications: the autodialler automatically checks the presence/absence of the 2W speaker units
flexible system and easy-to-expand
interference-free

pn:

5HL-300; 5HL-310; 5HL-320

Max Handsfree32

Services

Alarm calls and periodic test calls management as per EN81-28:2018
Telephone numbers: programmable, up to 12
Supported voice terminals: 16 2W speaker units, max 32 with passive units
Digital volume adjustment
Advanced self-diagnosis system
Programming modes: local or remote via phone, SMS, PC with e-stant software and USB cable, micro SD Card
Missed test call notification in the car as per EN 81-28:2018 standard
Low battery signalling: via device status LED
Telephone line presence check
VoIP compatibility: with analog output or ATA adapter
Alarm sending modes: voice, CLI, SMS, esse-ti protocol, P100
Voice prompts: menu with 8 languages, customizable with e-stant software
Alarm ending: with or without entering codes
2 Relays: programmable, multifunction (only 5HL-300; 5HL-310)
Technological alarms: absence of 2W handsfree terminal connection, low battery, battery replacement, power supply failure, diagnostics, auxiliary
Multi-Sharing function (with GSM200-C gateway): simultaneous notification of the same alarm to different receivers
Multi-link function: up to 9 autodiallers can be connected over 1 telephone line
Relay contacts function management (same behavior as output AI or AR / active for mains failure / door opener / active as long as the emergency alarm progresses / active as long as the buttons are pressed / active with no telephone line / active with low battery)
SD Card: extended LOG, firmware update, messages and programming.

Download

Hardware and Software design and development carried out at the Esse-ti Research Center. 100% made in Italy.

Compliant: EN 81-80, EN 81-28, EN 81-70

TECHNICAL FEATURES

Power supply features
Power supply: 12 VDC nominal, 11,5 VDC min., 14 VDC max.
Absorption in idle state: <55 mA over PSTN line; <100 mA with GSM200-C
Absorption alarm conversation mode: <160 mA over PSTN line; <240 mA with GSM200-C Self-restorable fuse on power supply input
Internal voltages: +1,8 V , +3,3 V, +5 V
Data transmission and signalling system
Built-in Modem v.23 if connected to PSTN line: 300-1200 bps
FSK GSM Modem if connected to GSM200-C module: 9600 bps
Type of dialing over external line: DTMF
DTMF generator
External line tone recognition: 85 countries
Protocols
Remote programming protocol: proprietary
Service center protocols: P100, Esse-ti
Other protocols upon request
Voice Messages
Pre-recorded languages: 8 (Italian / English / German / French / Polish / Portuguese / Spanish / Russian)
Pre-recorded voice messages: 30 minutes, restorable
Messages that support the programming
Alarm messages
Elevator identification message: customizable (max. 25 s)
Courtesy message for the car: multi-language, customizable (max. 25 s)
Messages customization: via computer (via USB-serial cable and software e-stant) / via micro SD card
Telephone terminations
Connection to public telephone network or universal GSM gateway: terminal block over optional PSTN-line board
Connection to GSM200-C module: plug RJ-45
Local telephone connection: plug RJ11 / terminal block
2-wire bus for the connection of 2W speaking units: terminal block
Up to 16 2W speaking units connection (4 with direct power supply from the bus and 12 with separate power supply)
Input/output
Reset pushbutton
Alarm inputs: 1
Customizable inputs (alarm / auxiliary / reset input): 1
Filter inputs: 1 (programmable as reset input)
Gong inputs: 1 (programmable as auxiliary input)
Relay outputs: 2, programmable (max. 250 Vac or 220 Vdc), over optional board
Outputs (alarm given, alarm received): 2 LED signalling device status: 1
LED signalling GSM200-C signal: 1
Esse-ti power supply input: 1
Serial port for PC connection: 1
Serial port for elevator CPU connection: 1
Micro SD Card slot
Safety systems
EEPROM for data storage under power failure
Built-in NiCd battery for clock data storage
Double watchdog system
Additional data
Mounting: plastic DIN rail
Dimensions (with plastic rail): 112x90x50(h) mm
Dimensions with optional boards (with plastic rail): 112x90x56(h) mm Weight: 148 g