Helpy 2W-V

Utra-compact autodialler with metal case for COP and or car-top installation. Inclusive of speech module and LEDs signalling alarm sent and alarm received. PSTN-line ready, expandible over GSM network.
Helpy 2W-V is the 2-wire solution to be installed behind the elevator car panel or on the lift car-top. Thanks to the built-in speech unit and its small dimensions is ideal for platforms. Available in 12V version and 24V version.
New 2-wires autodiallers:
- reduced cabling and enhanced installation costs: enhanced diagnostic and reduced wiring thanks to the new proprietary 2W-BUS
- complete range of autodiallers and dedicated 2E speaking units: depending on the installation, it is possible to choose the perfect-matching solution for any installation with the utmost quality-speech
- pedriodic BUS check: the autodialler automatically checks the presence/absence of the 2W speaking units with programmable notifications
- flexible system and easy-to-expand
- interference-free
Services
- Alarm calls and periodic test calls management as per UNI EN81-28:2018
- Telephone numbers: programmable, up to 12
- Supported voice terminals: up to 8 add-on speaking units (32 with auxiliary BUS power supply)
- Digital volume adjustment
- Advanced self-diagnosis system
- Programming modes: local or remote via phone, SMS, PC with e-stant software and USB cable, micro SD Card
- Missed test call notification in the car as per EN 81-28:2018 standard
- Low battery signalling: via device status LED
- Telephone line presence check
- VoIP compatibility: with analog output or ATA adapter
- Alarm sending modes: voice, CLI, SMS, esse-ti protocol, P100
- Voice prompts: menu with 8 languages, customizable with e-stant software
- Alarm ending: with or without entering codes
- Relay: programmable, multifunction
- Technological alarms: absence of 2W handsfree terminal connection, low battery, battery replacement, power supply failure, diagnostics, auxiliary
- Multi-link function: up to 9 autodiallers can be connected over 1 telephone line
- Relay contacts function management (same behavior as output AI or AR / active for mains failure / door opener / active as long as the emergency alarm progresses / active as long as the buttons are pressed / active with no telephone line / active with low battery)
- SD Card: extended LOG, firmware update, messages and programming.
Download
Compliant: EN 81-80, EN 81-28, EN 81-70
TECHNICAL FEATURES
Absorption alarm conversation mode: 190 mA
Self-restorable fuse on power supply input
Internal voltages: +1,8 V , +3,3 V, +5 V
Absorption alarm conversation mode: 140 mA
Self-restorable fuse on power supply input
Internal voltages: +1,8 V , +3,3 V, +5 V
Data transmission and signalling system
Built-in Modem v.23: 300-1200 bps FSK
Telephone line tones recognition: 85 countries
Telephone terminations
Connection to public telephone network or universal GSM gateway: terminal block
Local telephone connection: plug RJ11 / terminal block
Built-in speaking unit
Auxiliary microphone inputs: 2
Auxiliary loudspeaker outputs: 1 (to connect max. 2 passive speaking units or loudspeakers)
Voice messages
Pre-recorded voice messages: 30 minutes, restorable
Messages that support the programming
Alarm messages
Elevator identification message: customizable (max. 25 s)
Courtesy message for the car: multi-language, customizable (max. 25 s)
Messages customization: via computer (via USB-serial cable and software e-stant) / via micro SD card
Given alarm indicator light
Received alarm indicator light
Reset pushbutton
Alarm inputs: 1
Customizable inputs (alarm / auxiliary / reset input): 1 Filter inputs: 1 (programmable as reset input)
Relay outputs: 1, programmable (max. 250 Vac or 220 Vdc) Outputs (alarm given, alarm received): 2
LED signalling device status: 1
Serial port for PC connection: 1
Micro SD Card slot
Safety systems
EEPROM for data storage under power failure
Built-in NiCd battery for clock data storage
Double watchdog system
Firmware update and programming pattern
Additional data
Dimensions: 157x96x28 mm